Blade RF 2.0 Micro xA4

The Blade RF 2.0 Micro xA4 is the undisputed SDR champion, boasting unmatched frequency range, huge bandwidth, incredible on-board processing capacity backed with full software support. For penetration testers, the killer-feature is the ability to run 3G/LTE Base-Stations via OpenBTS, allowing testing, manipulation and MITM for cellular IOT devices. The Standard Pack contains everything needed to build a BTS: RX and TX amplifiers and 4x GSM antennas. The Deluxe Pack contains 4x Wide-Band general purpose antennas to extend your testing surface. Overview The BladeRF is a mature, wide-band full duplex 2x2 MIMO RF transceiver, covering 47MHz to 6GHz. It is compatible with all major SDR suites across multiple platforms: GNU Radio via gr-osmosdr, Pothos via SoapySDR, SDRange, SDR Console, SDR # via sdrsharp-bladeRF, MathWorks MATLAB® & Simulink® via libbladeRF bindings. BladeRF libraries, utilities, firmware and HDL are open source with public schematics. There are extensive SDKs available free of charge. The wide-band range, extensive bandwidth and full duplex capabilities make the BladeRF the ideal tool for multiple use-cases: Remote Control Analysis: Analyse, replay and emulate car remotes, alarms, garage remotes, etc. GPS Manipulation: Block, manipulate or adjust GPS signals for location-aware devices MITM GSM devices: Capture and manipulate data from cellular IOT devices. Advanced RFID Analysis: Analyse and communicate with all RFID tags, regardless of their frequency. Standard SDR functionality: ADB-S Tracking, satellite-communication, packet-sniffing, signal analysis, etc USB 3.0 Superspeed Capture & process at 5Gbps full-duplex Onboard programmable FPGA Write apps directly on-board. Built for professionals Built to exceed standards and expectations. Community Backed Plug'n'Play compatible with all major SDR suites. Ready to go Comes with everything, including antennas. BladeRF Packs Lab401 provides two BladeRF configurations or packs.Use our guide below to understand which pack is best suited to your needs. Starter PackThe Starter Pack provides the minimum configuration required for creating a BTS in laboratory conditions. The BladeRF's powerful architecture has made it the "go-to" BTS solution. If you're looking to get started with GSM/S7/OpenBTS hacking - this is the pack for you. Deluxe PackBuilt on the foundations of the Starter Park, the Deluxe Pack provides the complete SDR & BTS configuration - in the laboratory and in the field. With a full-range of antennas and and two amplifiers, the Deluxe Pack is aimed for real-world SDR exercises and in-the-field BTS pen-test operations - and everything in between. The full pack breakdown is below: Package Contents Product Starter Deluxe Description BladeRF 2.0 micro xA4 ✔️ ✔️ BladeRF Mainboard: 47MHz to 6GHz frequency range BladeRF Case ✔️ ✔️ Clear Polycarbonate case GSM Antenna (x2) ✔️ GSM Antennas optimised for BTS usage GSM Antenna (x4) ✔️ GSM Antennas optimised for BTS usage BT-100 Bias-Tee Amplifier (x2) ✔️ Wideband bias tee TX Power Amplifier BT-200 Bias Tee Amplifier (x2) ✔️ BT-200 is a wideband bias-tee RX Low Noise Amplifier Tri-Band Antenna (x4) ✔️ General purpose tri-band antenna that covers 700MHz to 2600MHz RF Specifications RF Specifications Min Max Unit ADC/DAC Sample Rate 0.521 61.44 MSPS ADC/DAC Resolution 12 bits RF Tuning Range (RX) 70 6000 MHz RF Tuning Range (TX) 47 6000 MHz RF Bandwidth Filter <0.2 56 MHz CW Output Power +8 dBm FPGA Specifications FPGA Specifications Min Max Unit Logic Elements 49 kLE Memory 3,383 kbits Variable-precision DSP blocks 66 342 Embedded 18x18 Multipliers 132 684 What's included Starter Pack 1x bladeRF 2.0 micro xA4 1x bladeRF 2.0 micro case 2x GSM Antennas 1x USB 3.0 SS Cable Deluxe Pack 1x bladeRF 2.0 micro xA4 1x bladeRF 2.0 micro case 2x BT-100 Bias-Tee TX Amplifier 2x BT-200 Bias-Tee RX Amplifier 4x GSM Antennas 4x Tri-Band General Purpose Antennas 1x USB 3.0 SS Cable Shipping & Packaging Each bladeRF is dispatched from Europe - no need to worry about slow shipping times, import duties or damaged goods. Packed in a sturdy compact 85x130x45mm box. We provide worldwide shipping with express options. Compatible Systems Windows/macOS/Linux/Android (Specific Builds) GNU Radio via gr-osmosdr, Pothos via SoapySDR, SDRange, SDR Console, SDR # via sdrsharp-bladeRF, MathWorks MATLAB® & Simulink® via libbladeRF bindings. BladeRF Resources Technical Documents bladeRF Product Brief libbladeRF API documentation An SDR-Based FRS Transceiver (PDF) GNU Radio flowgraph is available here Firmware Images FPGA bitstreams FX3 firmware Useful Links Source code on GitHub bladeRF Wiki bladeRF VCTCXO factory calibration lookup SDR-Radio SDRAngel Airspy SRS-LTE OpenAirInterface (Ensure you use `develop' branch) SDR# Github SDR# precompiled binaries YateBTS installation instructions (v1.0 only) Yate and YateBTS source code tarball with readme (v2.0) use v1.0 instructions (link above) RC (LATEST) Yate and YateBTS source code tarball with readme (v2.0) use v1.0 instructions (link above)